rockchip
This commit is contained in:
zhangpeng
384
rk3562-test1-ddr3-v10.dtsi
Normal file
384
rk3562-test1-ddr3-v10.dtsi
Normal file
@@ -0,0 +1,384 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Copyright (c) 2022 Rockchip Electronics Co., Ltd.
|
||||
*
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "rk3562.dtsi"
|
||||
#include "rk3562-evb.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/pinctrl/rockchip.h>
|
||||
|
||||
/ {
|
||||
model = "Rockchip RK3562 TEST1 DDR3 V10 Board";
|
||||
compatible = "rockchip,rk3562-test1-ddr3-v10", "rockchip,rk3562";
|
||||
|
||||
dc_12v: dc-12v {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "dc_12v";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <12000000>;
|
||||
regulator-max-microvolt = <12000000>;
|
||||
};
|
||||
|
||||
rk809_sound: rk809-sound {
|
||||
status = "okay";
|
||||
compatible = "rockchip,multicodecs-card";
|
||||
rockchip,card-name = "rockchip-rk809";
|
||||
hp-det-gpio = <&gpio3 RK_PC6 GPIO_ACTIVE_LOW>;
|
||||
rockchip,format = "i2s";
|
||||
rockchip,mclk-fs = <256>;
|
||||
rockchip,cpu = <&sai2>;
|
||||
rockchip,codec = <&rk809_codec>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&hp_det>;
|
||||
};
|
||||
|
||||
sdio_pwrseq: sdio-pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
clocks = <&rk809 1>;
|
||||
clock-names = "ext_clock";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_enable_h>;
|
||||
|
||||
/*
|
||||
* On the module itself this is one of these (depending
|
||||
* on the actual card populated):
|
||||
* - SDIO_RESET_L_WL_REG_ON
|
||||
* - PDN (power down when low)
|
||||
*/
|
||||
post-power-on-delay-ms = <200>;
|
||||
reset-gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
vcc5v0_sys: vcc5v0-sys {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc5v0_sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
vin-supply = <&dc_12v>;
|
||||
};
|
||||
|
||||
vcc5v0_usb: vcc5v0-usb {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc5v0_usb";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
vin-supply = <&dc_12v>;
|
||||
};
|
||||
|
||||
vcc5v0_usb_host: vcc5v0-usb-host {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc5v0_usb_host";
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
vin-supply = <&vcc5v0_usb>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb_host_pwren>;
|
||||
};
|
||||
|
||||
vcc5v0_usb_otg: vcc5v0-usb-otg {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc5v0_usb_otg";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
|
||||
vin-supply = <&vcc5v0_usb>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb_otg_pwren>;
|
||||
};
|
||||
|
||||
vcc3v3_clk: vcc3v3-clk {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc3v3_clk";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&vcc5v0_sys>;
|
||||
};
|
||||
|
||||
vcc3v3_sys: vcc-sys {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc3v3_sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&dc_12v>;
|
||||
};
|
||||
|
||||
vcc25_ddr: vcc25-ddr {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc25_ddr";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <2500000>;
|
||||
regulator-max-microvolt = <2500000>;
|
||||
vin-supply = <&vcc3v3_sys>;
|
||||
};
|
||||
|
||||
vdd_npu: vdd-npu {
|
||||
compatible = "pwm-regulator";
|
||||
pwms = <&pwm6 0 5000 1>;
|
||||
regulator-name = "vdd_npu";
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <1100000>;
|
||||
regulator-init-microvolt = <900000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-settling-time-up-us = <250>;
|
||||
pwm-supply = <&vcc5v0_sys>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
wireless-wlan {
|
||||
compatible = "wlan-platdata";
|
||||
rockchip,grf = <&sys_grf>;
|
||||
wifi_chip_type = "ap6275s";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_host_wake_irq>;
|
||||
WIFI,host_wake_irq = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
|
||||
WIFI,poweren_gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
wireless-bluetooth {
|
||||
compatible = "bluetooth-platdata";
|
||||
clocks = <&rk809 1>;
|
||||
clock-names = "ext_clock";
|
||||
//wifi-bt-power-toggle;
|
||||
uart_rts_gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default", "rts_gpio";
|
||||
pinctrl-0 = <&uart1m0_rtsn>;
|
||||
pinctrl-1 = <&uart1_gpios>;
|
||||
BT,reset_gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
BT,wake_gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
|
||||
BT,wake_host_irq = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&combphy_pu {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dsi {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dsi_in_vp0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dsi_panel {
|
||||
power-supply = <&vcc3v3_lcd_n>;
|
||||
reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_rst_gpio>;
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
/* Use rgmii-rxid mode to disable rx delay inside Soc */
|
||||
phy-mode = "rgmii-rxid";
|
||||
clock_in_out = "output";
|
||||
|
||||
snps,reset-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-active-low;
|
||||
/* Reset time is 20ms, 100ms for rtl8211f */
|
||||
snps,reset-delays-us = <0 20000 100000>;
|
||||
|
||||
tx_delay = <0x3f>;
|
||||
/* rx_delay = <0x3f>; */
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmiim1_miim
|
||||
&rgmiim1_tx_bus2
|
||||
&rgmiim1_rx_bus2
|
||||
&rgmiim1_rgmii_clk
|
||||
&rgmiim1_rgmii_bus
|
||||
ðm1_pins>;
|
||||
|
||||
phy-handle = <&rgmii_phy>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
>1x {
|
||||
compatible = "goodix,gt1x";
|
||||
reg = <0x14>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&touch_gpio>;
|
||||
goodix,rst-gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
|
||||
goodix,irq-gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
|
||||
/*
|
||||
* power-supply should switche to vcc3v3_lcd1_n
|
||||
* when mipi panel is connected to dsi1.
|
||||
*/
|
||||
power-supply = <&vcc3v3_lcd_n>;
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
rgmii_phy: phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0x1>;
|
||||
clocks = <&cru CLK_GMAC_ETH_OUT2IO>;
|
||||
assigned-clocks = <&cru CLK_GMAC_ETH_OUT2IO>;
|
||||
assigned-clock-rates = <25000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
headphone {
|
||||
hp_det: hp-det {
|
||||
rockchip,pins = <3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
lcd {
|
||||
lcd_rst_gpio: lcd-rst-gpio {
|
||||
rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
sdio-pwrseq {
|
||||
wifi_enable_h: wifi-enable-h {
|
||||
rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
touch {
|
||||
touch_gpio: touch-gpio {
|
||||
rockchip,pins =
|
||||
<0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
|
||||
<0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
usb {
|
||||
usb_host_pwren: usb-host-pwren {
|
||||
rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
|
||||
usb_otg_pwren: usb-otg-pwren {
|
||||
rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
wireless-wlan {
|
||||
wifi_host_wake_irq: wifi-host-wake-irq {
|
||||
rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_down>;
|
||||
};
|
||||
};
|
||||
|
||||
wireless-bluetooth {
|
||||
uart1_gpios: uart1-gpios {
|
||||
rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&route_dsi {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sai2 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2s2m1_lrck
|
||||
&i2s2m1_sclk
|
||||
&i2s2m1_sdi
|
||||
&i2s2m1_sdo>;
|
||||
};
|
||||
|
||||
&sdmmc0 {
|
||||
no-sd;
|
||||
no-mmc;
|
||||
bus-width = <4>;
|
||||
disable-wp;
|
||||
cap-sd-highspeed;
|
||||
cap-sdio-irq;
|
||||
keep-power-in-suspend;
|
||||
mmc-pwrseq = <&sdio_pwrseq>;
|
||||
non-removable;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd>;
|
||||
sd-uhs-sdr104;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdmmc1 {
|
||||
no-sdio;
|
||||
no-mmc;
|
||||
bus-width = <4>;
|
||||
cap-mmc-highspeed;
|
||||
cap-sd-highspeed;
|
||||
disable-wp;
|
||||
sd-uhs-sdr104;
|
||||
vmmc-supply = <&vcc3v3_sd>;
|
||||
vqmmc-supply = <&vccio_sd>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_clk &sdmmc1_cmd &sdmmc1_det>;
|
||||
/* Should disable gmac0 and fix hardware if enabling sdmmc1 */
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&pwm6 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&u2phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&u2phy_host {
|
||||
status = "okay";
|
||||
phy-supply = <&vcc5v0_usb_host>;
|
||||
};
|
||||
|
||||
&u2phy_otg {
|
||||
status = "okay";
|
||||
vbus-supply = <&vcc5v0_usb_otg>;
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
|
||||
};
|
||||
|
||||
&usb_host0_ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_host0_ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbdrd30 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbdrd_dwc3 {
|
||||
status = "okay";
|
||||
dr_mode = "otg";
|
||||
extcon = <&u2phy>;
|
||||
};
|
||||
|
||||
&vcc3v3_lcd_n {
|
||||
gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
&video_phy {
|
||||
status = "okay";
|
||||
};
|
||||
Reference in New Issue
Block a user