Radiation-resistantCamera/Vimba_6_0/VimbaCSITL/CTI/arm_64bit/VimbaCSITL.xml

<?xml version="1.0" standalone="no" ?>
<Settings>
    <!--
        Use this to activate logging and set filename for logging (path can be absolute or relative to TL)
        Default behavior if omitted:    Logging is deactivated
    -->
    <!-- <LogFileName>VimbaCSITL.log</LogFileName> -->


    <!--
        CSI logging: Use this to activate logging and set filename(path can be absolute or relative to TL)
        Default behavior if omitted:    Logging is deactivated
    -->
    <!-- <MediaLogFileName>VimbaCSI.log</MediaLogFileName> -->


    <!--
        Append messages to log file or reset log file at each transport layer restart (if logging is enabled)
        True:                           Always append log messages
        False:                          Reset log file at each transport layer restart
        Default behavior if omitted:    Reset log file at each transport layer restart
    -->
    <!-- <AppendLog>True</AppendLog> -->


    <!--
            Activate less pedantic function parameter checks (needed for some TL consumers)
            True:                           Tolerant function parameter checks
            False:                          Pedantic function parameter checks
            Default behavior if omitted:    Pedantic function parameter checks (GenTL compliant behavior)
    -->
    <TolerateTypeNullptr>True</TolerateTypeNullptr>


    <!--
            Emulate unsupported device access modes (needed for some TL consumers)
            True:                           Emulation on
            False:                          Emulation off
            Default behavior if omitted:    Emulation off (GenTL compliant behavior)
    -->
    <EmulateAccessModes>True</EmulateAccessModes>


    <!--
        Enable the repeated device enumeration.
        True:                           Activate repeated device enumeration every <EnumerationInterval>
        False:                          Deactivate repeated device enumeration. Devices are enumerated only once.
        Default behavior if omitted:    False
    -->
    <!-- <EnableEnumeration>False</EnableEnumeration> -->


    <!--
        Interval for each device enumeration loop (in milliseconds)
        Decimal and hexadecimal numbers (prefixed with "0x") can be used
        Default behavior if omitted:    Use 10000ms
    -->
    <!-- <EnumerationInterval>10000</EnumerationInterval> --> 


    <!--
			Number of frames to use for intermediate frame buffering. Values
            greater than 0 mean that no zero copy is possible anymore.
            Decimal and hexadecimal numbers (prefixed with "0x") can be used
            Default behavior if omitted:    0 (No intermediated frame buffering)
    -->
    <!-- <DriverBuffersCount>3</DriverBuffersCount> -->


    <!-- Enter manual settings for each camera port -->
    <Ports>
        <!-- ID specifies the port identifier of this specific port -->
        <Port ID="Port:0x01_Bus:0x04_Address:0x3C"> 
            <!--
                CSI lane count used during streaming of a device on this port.
                Supported values: 1, 2, 3, 4
                Decimal and hexadecimal numbers (prefixed with "0x") can be used
                Default behavior if omitted:    Maximum supported lane count will be used
            -->
            <!--<CSILaneCount>4</CSILaneCount>-->

            <!--
                CSI clock frequency (in Hz) used during streaming of a device on this port.
                The clock frequency actually used may be less if the desired value is
                not supported exactly.
                Decimal and hexadecimal numbers (prefixed with "0x") can be used
                Default behavior if omitted:    Maximum supported clock frequency will be used
            -->
            <!--<CSIClockFrequency>395000000</CSIClockFrequency>-->
        </Port>
    </Ports>


    <!--
        Set the folder in which remote device XML files will be cached
        Default behavior if omitted:    XML files will be cached
    -->
    <XMLCacheFolder>XMLCache</XMLCacheFolder>

</Settings>